Maple Leaf Quilt Block

A free cutting chart for 6", 9" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Maple Leaf is a leaf on a three-by-three grid: a background square in one corner, half-square triangles for the lobes along two sides, three leaf squares, and a stem unit running corner to corner in the last square.

  • 12 × 12 grid
  • 6", 9" and 12" finished
  • 2 fabrics
The Maple Leaf block as the Quiltler studio draws it.

What the Maple Leaf block is made of

Every shape in a 12" block, by fabric, at its finished size. Where a triangle sits on the corner of a square, the square is listed whole: it is cut whole and the corner sewn on top, stitch and flip.

FabricFinished shapes
Background1 square (4"), 4 half-square triangles (4") and 2 half-square triangles (3")
Leaf4 half-square triangles (4") and 4 squares (4")

The pattern sews it from 4 half-square triangle units (H1) and 1 stitch-and-flip corner unit (S1).

It goes together in 3 rows of 3: 1 background square, 4 half-square triangles, 3 leaf squares and 1 stem unit.

Maple Leaf cutting chart

Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

6" finished block (½" grid, 6½" unfinished)

FabricCutFor
Background2 squares 2⅞"H1: half-square triangles, two at a time
Background1 square 2½"Finishes at 2" square
Background2 squares 2"S1: stitch-and-flip corners
Leaf2 squares 2⅞"H1: half-square triangles, two at a time
Leaf1 square 2½"S1: stitch-and-flip corners
Leaf3 squares 2½"Finishes at 2" square

9" finished block (¾" grid, 9½" unfinished)

FabricCutFor
Background2 squares 3⅞"H1: half-square triangles, two at a time
Background1 square 3½"Finishes at 3" square
Background2 squares 2¾"S1: stitch-and-flip corners
Leaf2 squares 3⅞"H1: half-square triangles, two at a time
Leaf1 square 3½"S1: stitch-and-flip corners
Leaf3 squares 3½"Finishes at 3" square

12" finished block (1" grid, 12½" unfinished)

FabricCutFor
Background2 squares 4⅞"H1: half-square triangles, two at a time
Background1 square 4½"Finishes at 4" square
Background2 squares 3½"S1: stitch-and-flip corners
Leaf2 squares 4⅞"H1: half-square triangles, two at a time
Leaf1 square 4½"S1: stitch-and-flip corners
Leaf3 squares 4½"Finishes at 4" square

How to sew a 12" Maple Leaf block

Make the units

  1. Pair each Leaf square with a Background square, 4⅞" square, right sides together. Draw a line corner to corner on the back of the lighter one.
  2. Sew a quarter inch either side of the line, cut on the line and press open. Each pair makes two units.
  3. Make 4 units from 2 pairs. Each should measure 4½" square with seam allowance.
  4. Draw a line corner to corner on the back of each corner square: 2 × Background 3½" square for each unit.
  5. Lay one square on its corner of a Leaf piece, 4½" square, right sides together as the drawing shows, and sew on the line. Trim a quarter inch outside the seam and press the corner out, then sew, trim and press the other square the same way: the squares overlap, so they go on one at a time.
  6. Make 1 unit this way.

Sew the block

  1. The block takes 4 × H1 and 1 × S1; make them first.
  2. Lay out the units and pieces in 3 rows of 3 as the drawing shows.
  3. Row 1: sew background square (Background), half-square triangle (H1) and half-square triangle (H1) together, then press the seams to the right.
  4. Row 2: sew half-square triangle (H1), leaf square (Leaf) and leaf square (Leaf) together, then press the seams to the left.
  5. Row 3: sew half-square triangle (H1), leaf square (Leaf) and stem unit (S1) together, then press the seams to the right.
  6. Join the rows, nesting the seams where they meet, then press the seams open.
  7. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Maple Leaf blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Start a throw-size Maple Leaves quilt in the studio and recolor it in your own fabrics. To add the block to any other quilt, open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Maple Leaf. Click the block, then click a space on the quilt.

Start a Maple Leaves quilt

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Maple Leaf block FAQ

What do I cut for a 12" Maple Leaf block?

For one 12" finished Maple Leaf block, with a quarter-inch seam: Background: 2 squares 4⅞"; 1 square 4½"; 2 squares 3½". Leaf: 2 squares 4⅞"; 1 square 4½"; 3 squares 4½".

How many Maple Leaf blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Maple Leaf block be?

It is drafted on a 12 × 12 grid, so it works at any size that grid divides evenly. 6", 9" and 12" give ½", ¾" and 1" squares of the grid.

Design a Maple Leaf quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app