House on the Hill Quilt Block

A free cutting chart for 6", 8" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

House on the Hill is a four-by-four picture block: a roof made as one large flying-geese unit across the top half, a row of four wall squares below it, and a row of ground squares along the bottom.

  • 4 × 4 grid
  • 6", 8" and 12" finished
  • 4 fabrics
The House on the Hill block as the Quiltler studio draws it.

What the House on the Hill block is made of

Every shape in a 12" block, by fabric, at its finished size.

FabricFinished shapes
Sky2 half-square triangles (6")
Roof1 flying-geese triangle (12" × 6")
Wall4 squares (3")
Ground4 squares (3")

The pattern sews it from 1 flying-geese unit (G1), 1 pieced section (U1) and 4 strip-set segments (strip set 1).

House on the Hill cutting chart

Cut sizes for one block at 6", 8" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

6" finished block (1½" grid, 6½" unfinished)

FabricCutFor
Sky2 squares 3½"G1: flying geese, stitch and flip
Roof1 rectangle 6½" × 3½"G1: flying geese, stitch and flip
Wall1 strip 2" × WOF (half length is enough)Strip set 1
Ground1 strip 2" × WOF (half length is enough)Strip set 1

8" finished block (2" grid, 8½" unfinished)

FabricCutFor
Sky2 squares 4½"G1: flying geese, stitch and flip
Roof1 rectangle 8½" × 4½"G1: flying geese, stitch and flip
Wall1 strip 2½" × WOF (half length is enough)Strip set 1
Ground1 strip 2½" × WOF (half length is enough)Strip set 1

12" finished block (3" grid, 12½" unfinished)

FabricCutFor
Sky2 squares 6½"G1: flying geese, stitch and flip
Roof1 rectangle 12½" × 6½"G1: flying geese, stitch and flip
Wall1 strip 3½" × WOF (half length is enough)Strip set 1
Ground1 strip 3½" × WOF (half length is enough)Strip set 1

How to sew a 12" House on the Hill block

Make the units

  1. Draw a line corner to corner on the back of each of the 2 Sky squares, 6½" square.
  2. Lay a Sky square on one end of a Roof rectangle, 12½" × 6½", right sides together, with the line running from the bottom outer corner to the top edge. Sew on the line, trim a quarter inch outside it and press the sky out. Repeat at the other end, the second line crossing the first a quarter inch below the top edge, where the goose's point will be.
  3. Make 1 goose this way, one at a time. Each should measure 12½" × 6½" with seam allowance.

Sew the strip sets

  1. Sew 2 strips together along their long edges in this order: Wall – Ground.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 half-length set from strips cut in half.
  4. Trim one end square, then crosscut 4 segments 3½" wide. Square the end again every few cuts.
  5. Use the segments for columns 1, 2, 3 and 4 of unit U1.

Sew unit U1

  1. Unit U1 takes 4 segments of strip set 1.
  2. Lay the segments out as the drawing shows.
  3. Join the columns, matching the seams where they meet.
  4. Each unit U1 should measure 12½" × 6½" including seam allowance. Check it against the drawing.

Sew the block

  1. The block takes 1 × G1 and 1 × unit U1; make them first.
  2. Sew the 2 sections together top to bottom, in the order the drawing shows.
  3. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many House on the Hill blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for House on the Hill. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

House on the Hill block FAQ

What do I cut for a 12" House on the Hill block?

For one 12" finished House on the Hill block, with a quarter-inch seam: Sky: 2 squares 6½". Roof: 1 rectangle 12½" × 6½". Wall: 1 strip 3½" × WOF (half length is enough). Ground: 1 strip 3½" × WOF (half length is enough).

How many House on the Hill blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a House on the Hill block be?

It is drafted on a 4 × 4 grid, so it works at any size that grid divides evenly. 6", 8" and 12" give 1½", 2" and 3" squares of the grid.

Design a House on the Hill quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app