Wings Quilt Block

A free cutting chart for 6", 8" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Wings is a four-by-four block: a band of accent across the middle that rises in a V to the two top corners, shaped by four half-square triangles, above a plain row of background squares along the bottom.

  • 4 × 4 grid
  • 6", 8" and 12" finished
  • 2 fabrics
The Wings block as the Quiltler studio draws it.

What the Wings block is made of

Every shape in a 12" block, by fabric, at its finished size.

FabricFinished shapes
Background6 squares (3") and 4 half-square triangles (3")
Accent4 half-square triangles (3") and 6 squares (3")

The pattern sews it from 1 pieced section (U1), 4 half-square triangle units (H1), 1 pieced section (U2) and 4 strip-set segments (strip set 1).

Wings cutting chart

Cut sizes for one block at 6", 8" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

6" finished block (1½" grid, 6½" unfinished)

FabricCutFor
Background1 strip 2" × WOF (half length is enough)Strip set 1
Background2 squares 2⅜"H1: half-square triangles, two at a time
Background2 squares 2"Finishes at 1½" square
Accent1 strip 2" × WOF (half length is enough)Strip set 1
Accent2 squares 2⅜"H1: half-square triangles, two at a time
Accent2 squares 2"Finishes at 1½" square

8" finished block (2" grid, 8½" unfinished)

FabricCutFor
Background1 strip 2½" × WOF (half length is enough)Strip set 1
Background2 squares 2⅞"H1: half-square triangles, two at a time
Background2 squares 2½"Finishes at 2" square
Accent1 strip 2½" × WOF (half length is enough)Strip set 1
Accent2 squares 2⅞"H1: half-square triangles, two at a time
Accent2 squares 2½"Finishes at 2" square

12" finished block (3" grid, 12½" unfinished)

FabricCutFor
Background1 strip 3½" × WOF (half length is enough)Strip set 1
Background2 squares 3⅞"H1: half-square triangles, two at a time
Background2 squares 3½"Finishes at 3" square
Accent1 strip 3½" × WOF (half length is enough)Strip set 1
Accent2 squares 3⅞"H1: half-square triangles, two at a time
Accent2 squares 3½"Finishes at 3" square

How to sew a 12" Wings block

Make the units

  1. Pair each Accent square with a Background square, 3⅞" square, right sides together. Draw a line corner to corner on the back of the lighter one.
  2. Sew a quarter inch either side of the line, cut on the line and press open. Each pair makes two units.
  3. Make 4 units from 2 pairs. Each should measure 3½" square with seam allowance.

Sew the strip sets

  1. Sew 2 strips together along their long edges in this order: Accent – Background.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 half-length set from strips cut in half.
  4. Trim one end square, then crosscut 4 segments 3½" wide. Square the end again every few cuts.
  5. Use the segments for columns 1, 2, 3 and 4 of unit U2.

Sew unit U1

  1. Unit U1 takes 4 × H1; make them first.
  2. Sew each row of Unit U1 together left to right, as the drawing shows. Press the seam allowances in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. Each unit U1 should measure 12½" × 6½" including seam allowance. Check it against the drawing.

Sew unit U2

  1. Unit U2 takes 4 segments of strip set 1.
  2. Lay the segments out as the drawing shows.
  3. Join the columns, matching the seams where they meet.
  4. Each unit U2 should measure 12½" × 6½" including seam allowance. Check it against the drawing.

Sew the block

  1. The block takes 1 × unit U1 and 1 × unit U2; make them first.
  2. Sew the 2 sections together top to bottom, in the order the drawing shows.
  3. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Wings blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Wings. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Wings block FAQ

What do I cut for a 12" Wings block?

For one 12" finished Wings block, with a quarter-inch seam: Background: 1 strip 3½" × WOF (half length is enough); 2 squares 3⅞"; 2 squares 3½". Accent: 1 strip 3½" × WOF (half length is enough); 2 squares 3⅞"; 2 squares 3½".

How many Wings blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Wings block be?

It is drafted on a 4 × 4 grid, so it works at any size that grid divides evenly. 6", 8" and 12" give 1½", 2" and 3" squares of the grid.

Design a Wings quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app