Sawtooth Star Quilt Block

A free cutting chart for 6", 8" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

The Sawtooth Star is a star on a four-by-four grid: a large center square, four flying-geese units whose small triangles are the star points, and a plain square in each corner. Because the points are geese, every seam is straight and nothing is set in.

  • 4 × 4 grid
  • 6", 8" and 12" finished
  • 2 fabrics
The Sawtooth Star block as the Quiltler studio draws it.

What the Sawtooth Star block is made of

Every shape in a 12" block, by fabric, at its finished size.

FabricFinished shapes
Background4 flying-geese triangles (6" × 3") and 4 squares (3")
Star1 square (6") and 8 half-square triangles (3")

The pattern sews it from 4 flying-geese units (G1).

It goes together in 3 rows of 3: 4 corner squares, 4 star points and 1 center square.

Sawtooth Star cutting chart

Cut sizes for one block at 6", 8" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

6" finished block (1½" grid, 6½" unfinished)

FabricCutFor
Background1 square 4¼"G1: flying geese, four at a time with no waste
Background4 squares 2"Finishes at 1½" square
Star1 square 3½"Finishes at 3" square
Star4 squares 2⅜"G1: flying geese, four at a time with no waste

8" finished block (2" grid, 8½" unfinished)

FabricCutFor
Background1 square 5¼"G1: flying geese, four at a time with no waste
Background4 squares 2½"Finishes at 2" square
Star1 square 4½"Finishes at 4" square
Star4 squares 2⅞"G1: flying geese, four at a time with no waste

12" finished block (3" grid, 12½" unfinished)

FabricCutFor
Background1 square 7¼"G1: flying geese, four at a time with no waste
Background4 squares 3½"Finishes at 3" square
Star1 square 6½"Finishes at 6" square
Star4 squares 3⅞"G1: flying geese, four at a time with no waste

How to sew a 12" Sawtooth Star block

Make the units

  1. Lay two Star squares, 3⅞" square, on opposite corners of a Background square, 7¼" square, right sides together; they overlap in the middle. Draw a line corner to corner across both.
  2. Sew a quarter inch either side of the line, cut on the line and press the small triangles out.
  3. Lay one more Star square on the corner of each piece, draw a line corner to corner, sew either side of it, cut and press. Each set makes four geese.
  4. Make 1 set (4 geese). Each should measure 6½" × 3½" with seam allowance.

Sew the block

  1. The block takes 4 × G1; make them first.
  2. Lay out the units and pieces in 3 rows of 3 as the drawing shows.
  3. Rows 1 and 3: sew corner square (Background), star point (G1) and corner square (Background) together, then press the seams toward the corner squares.
  4. Row 2: sew star point (G1), center square (Star) and star point (G1) together, then press the seams toward the center square.
  5. Join the rows, nesting the seams where they meet, then press the seams open.
  6. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Sawtooth Star blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Start a throw-size Sawtooth Stars quilt in the studio and recolor it in your own fabrics. To add the block to any other quilt, open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Sawtooth Star. Click the block, then click a space on the quilt.

Start a Sawtooth Stars quilt

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Sawtooth Star block FAQ

What do I cut for a 12" Sawtooth Star block?

For one 12" finished Sawtooth Star block, with a quarter-inch seam: Background: 1 square 7¼"; 4 squares 3½". Star: 1 square 6½"; 4 squares 3⅞".

How many Sawtooth Star blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Sawtooth Star block be?

It is drafted on a 4 × 4 grid, so it works at any size that grid divides evenly. 6", 8" and 12" give 1½", 2" and 3" squares of the grid.

Design a Sawtooth Star quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app