A worked answer

What Stitch Length and Seam Allowance for Quilt Binding?

Most quilters sew binding on with a 1/4 inch seam and a stitch of about 2.5 to 3 mm (about 8 to 10 stitches per inch), a little longer than for piecing because the needle goes through the binding, top, batting and backing at once. A 2 1/2 inch strip is also often sewn with a 3/8 inch seam for a fuller binding; whatever seam you choose, stop that same distance from each corner to miter it.

A pieced quilt with double-fold binding around the outer edge
Binding is the strip that wraps the outer edge. The calculator turns the perimeter into strips and yardage.

These are the settings quilt shops' and sewing machine makers' binding guides agree on. Where they differ, the table gives both. All of them assume double-fold binding, folded in half before it is sewn on.

Binding settings at a glance

StepMost quilters useWhy
Seam, 2 1/4 in strips1/4 inFills the binding on a thin, flat quilt
Seam, 2 1/2 in strips1/4 in, or 3/8 in1/4 in leaves room for thicker batting; 3/8 in gives a fuller binding on a thin quilt
Stitch, sewing binding on2.5 to 3 mmLonger than piecing, to feed evenly through the layers
Stop before a cornerThe seam allowanceSo the fold makes a true 45 degree miter
Finish by machineIn the ditch from the front, or topstitchedCatches the back of the binding from the right side
Finish by handBlind or slip stitchSmall stitches through the backing only, so nothing shows on the front

1/4 or 3/8 inch seam?

A binding finishes on the front as wide as the seam it was sewn with, because the fold wraps right up to the stitching. A 1/4 inch seam gives a 1/4 inch binding, a 3/8 inch seam a 3/8 inch one. The quilt inside fills the binding only as far as the seam, so the wider seam also packs more quilt into the fold.

Half of a double-fold strip goes round the edge. The seam allowance tucked under the binding, the front from the seam to the edge, and the back up to the stitching each take one seam's width of it, and the rest wraps the thickness of the quilt. With a 1/4 inch seam, a 2 1/4 inch strip leaves 3/8 inch for that and a 2 1/2 inch strip 1/2 inch, room for a thicker batting. A 3/8 inch seam on a 2 1/2 inch strip leaves 1/8 inch, so it suits a thin, flat quilt, where it gives a fuller, firmer edge than a 1/4 inch seam would. If your 2 1/2 inch binding feels soft and empty at the edge of a thin quilt, the 3/8 inch seam is the cure; on a thick quilt, keep the 1/4 inch seam. The strip width itself is in how wide to cut quilt binding.

Whichever you choose, keep it the same all the way round, and stop that far from every corner.

Stitch length

Sewing the binding on goes through the doubled binding, the top, the batting and the backing, so most guides lengthen the stitch from the short one used for piecing to 2.5 to 3 mm (about 8 to 10 stitches per inch). A longer stitch feeds more evenly through the layers and is easier to unpick if the seam wanders. A walking foot or a built-in dual feed keeps the binding and the quilt moving together, so the binding doesn't stretch or ripple.

Joining the strips to each other is ordinary piecing, at your usual stitch. A quilt with a fleece or minky back wants a longer stitch still; that is in binding a minky-backed quilt.

Mitering the corners

  1. Sew along the first side and stop as far from the corner as your seam allowance: 1/4 inch with a 1/4 inch seam, 3/8 inch with a 3/8 inch seam. Backstitch and take the quilt out from under the needle.
  2. Fold the binding straight up, away from the quilt, so it makes a 45 degree fold at the corner.
  3. Fold it back down along the next side, with the top fold level with the edge you just sewed.
  4. Start sewing again at that folded edge, with the same seam allowance, down the next side.

When the binding is folded to the back, those folds make 45 degree miters on both sides. The full sequence, from leaving the first tail to joining the two ends, is in How to Bind a Quilt.

Hand or machine finish

The binding is always sewn on by machine. The difference is how the folded edge is held down on the other side.

  • By hand. Sew the binding to the front, fold it to the back so it just covers the stitching line, and sew the fold down with a blind or slip stitch in thread that matches the binding, catching only the backing so nothing shows on the front. Binding clips hold the fold while you work. It is slower, and it is the traditional finish for a bed or show quilt.
  • By machine. Sew the binding to the front, fold it to the back so it reaches a little past the stitching line, hold it with clips or a dab of washable glue, then stitch in the ditch from the front, beside the binding, catching the back of the binding as you go. Or sew it to the back first and topstitch near the fold on the front. It is quick and strong, which suits baby quilts and anything washed often.

Work it out for your own quilt

How much binding to cut. The binding calculator gives the strips and the fabric for any size and strip width; curved edges need the bias binding calculator. Both are in the studio under Calculators, and a quilt designed in the studio counts its binding with the rest of its fabric.

Step-by-step in Quiltler

More quick answers

FAQ

What stitch length do you use to sew on quilt binding?

Most quilters use 2.5 to 3 mm (about 8 to 10 stitches per inch), a little longer than a piecing stitch, because of the layers. Use a walking foot.

What seam allowance for 2 1/2 inch binding?

1/4 inch is the most common. Many quilters use 3/8 inch with a 2 1/2 inch strip for a fuller binding; stop 3/8 inch from the corners if you do.

How far from the corner do you stop when binding a quilt?

The same distance as your seam allowance: 1/4 inch for a 1/4 inch seam, 3/8 inch for a 3/8 inch seam. Then fold the binding up at 45 degrees and back down to miter the corner.

What stitch do you use to hand-sew binding?

A blind or slip stitch in thread that matches the binding, catching only the backing so the stitches don't show on the front.

Design the quilt, then let the yardage follow

These calculators answer one question at a time. The studio counts every piece in a design, including binding, backing, and batting.

Design Online — Free Or get the companion app

Rated 4.4 stars on the App Store