A worked answer

How Wide to Cut Quilt Binding

Cut double-fold binding strips 2 1/2 inches wide for most quilts, or 2 1/4 inches for a narrower, snugger edge on thin cotton batting. Both finish about 1/4 inch wide on the front when sewn with a 1/4 inch seam; the extra 1/4 inch in a 2 1/2 inch strip is room to wrap a thicker quilt.

A pieced quilt with double-fold binding around the outer edge
Binding is the strip that wraps the outer edge. The calculator turns the perimeter into strips and yardage.

Why 2 1/4 or 2 1/2 inches

Double-fold binding is folded in half before it is sewn on, so a 2 1/2 inch strip is 1 1/4 inches of doubled fabric. Sewn to the front with a 1/4 inch seam, about 1/4 inch shows on the front. Round the back, the fold needs to reach a little past the stitching line, about 1/4 inch or a touch more. Whatever is left wraps the edge of the quilt: the thicker the batting, the more it takes.

  • 2 1/2 inches leaves enough to wrap most quilts, including polyester or two layers of batting, and still cover the stitching. It is the forgiving default, and the one the binding calculator opens on.
  • 2 1/4 inches is 1/8 inch narrower in the doubled strip. On thin cotton or 80/20 batting it gives a snug edge, filled right to the fold. On a puffy quilt it can come up short of the stitching on the back.
  • Wider bindings need wider strips and a wider seam together: a 3/8 or 1/2 inch seam with 2 3/4 to 3 inch strips. The binding width chart in the binding guide pairs them.

If you are not sure, sew a 10 inch test piece of binding onto a scrap sandwich of your batting and fold it to the back. A fleece, minky or sherpa back makes a thicker edge again: see binding a minky-backed quilt. The seam and stitch length to sew it on with are in binding stitch length and seam allowance.

How many binding strips for each bed size

From the binding calculator: the perimeter plus 10 inches for the corners and joins, in strips cut across 42 inch fabric. The strip count is the same at either width; only the fabric changes.

QuiltPerimeterStrips to cutFabric, 2 1/4 in stripsFabric, 2 1/2 in stripsBias, 2 1/2 in strips
Baby
36 × 52 in
176 in53/8 yard3/8 yard21 3/4 in square, 5/8 yard
Throw
50 × 65 in
230 in63/8 yard1/2 yard24 5/8 in square, 3/4 yard
Twin
70 × 90 in
320 in81/2 yard5/8 yard28 7/8 in square, 7/8 yard
Full / double
85 × 90 in
350 in95/8 yard5/8 yard30 1/8 in square, 7/8 yard
Queen
90 × 95 in
370 in105/8 yard3/4 yard31 in square, 7/8 yard
King
110 × 95 in
410 in105/8 yard3/4 yard32 1/2 in square, 1 yard

For a 90 × 95 inch queen: 2 × (90 + 95) = 370 inches, plus 10 is 380, and 380 ÷ 42 = 9.05, so 10 strips. At 2 1/2 inches that is 25 inches of fabric, 3/4 yard rounded up to the next eighth. Sizes are the quilt sizes guide's; more on each size in how much binding for a queen quilt and its sibling pages.

How to join binding strips on the diagonal

Strips are joined with a 45 degree seam rather than straight across. A straight seam stacks all of its seam allowance in one spot once the binding is folded and wrapped; a diagonal seam spreads it along about 2 1/2 inches, so the join disappears into the edge. Each diagonal join uses about one strip-width of length, which the 10 inch allowance covers.

  1. Cut the strips across the width of the fabric, selvage to selvage, and trim the selvages off.
  2. Lay one strip right side up, running left to right. Lay the next strip right side down across its end at a right angle, so the two ends overlap in a square.
  3. Draw a line across that square from the inside corner of the L, where the two strips cross, to the outside corner. Pin.
  4. Sew on the line. Before trimming, fold the top strip open to check the two run on in a straight line. If they kink, you sewed the other diagonal: unpick and sew the right one.
  5. Trim 1/4 inch beyond the seam and press the seam open, so the bulk spreads either side of it.
  6. Join the rest the same way, then fold the whole length in half, wrong sides together, and press.

The last join, where the two ends of the binding meet on the quilt, is the fiddly one. It is in How to Bind a Quilt, with sewing the binding on and mitering the corners.

Straight grain or bias?

Strips cut across the width of the fabric are on the crossgrain, with a little give. Strips cut along the length, parallel to the selvage, have almost none. Either is fine for straight edges and square corners, and both use less fabric than bias.

Bias strips are cut at 45 degrees to the grain, so they stretch and ease round a curve without puckering. Use bias binding for scalloped edges, curved or rounded corners, and round or oval quilts. Some quilters also bind straight-edged heirloom quilts on the bias, because no single thread runs along the fold to wear through. The bias binding calculator gives the square to cut for one continuous bias strip; the last column above is its answer at 2 1/2 inches.

Work it out for your own quilt

Any size, any strip width. The binding calculator takes your quilt's width and length, the strip width and the usable width of your fabric. The same calculator is in the studio under Calculators → Binding, and a quilt designed in the studio has its binding counted with the rest of its fabric.

Step-by-step in Quiltler

More quick answers

FAQ

Should I cut binding 2 1/4 or 2 1/2 inches?

2 1/2 inches for most quilts: it wraps any batting and is forgiving. 2 1/4 inches gives a snugger, flatter edge on thin cotton or 80/20 batting. Both finish about 1/4 inch wide on the front with a 1/4 inch seam.

How many binding strips do I need for a queen quilt?

10 strips cut across 42 inch fabric for a 90 × 95 inch queen: 3/4 yard at 2 1/2 inches, or 5/8 yard at 2 1/4 inches.

Why are binding strips joined on the diagonal?

A diagonal seam spreads the bulk of the join over a couple of inches, so it does not make a lump when the binding is folded and wrapped round the edge.

When do I need bias binding?

When the edge curves: scallops, rounded corners, round or oval quilts. Bias strips stretch round a curve. For straight edges and square corners, straight-grain binding is easier and uses less fabric.

Design the quilt, then let the yardage follow

These calculators answer one question at a time. The studio counts every piece in a design, including binding, backing, and batting.

Design Online — Free Or get the companion app

Rated 4.4 stars on the App Store