Project sizes

What Size Should a Table Runner Be?

Most table runners are 12 to 18 inches wide, about a third as wide as the table, and as long as the table plus 6 to 12 inches hanging off each end. For a 72 inch table that seats six, a 14 inch wide runner is 84 to 96 inches long.

A pieced quilt with double-fold binding around the outer edge
A runner is a long, thin quilt: bound like any other, with very little backing and batting.

There is no one standard size, because a runner is sized to its table. Measure the table, decide how far you want the runner to hang past each end, and add that twice. The width is a matter of looks: a third of the table's width leaves room for place settings on both sides, so a 36 to 42 inch wide table takes a runner 12 to 14 inches wide, and a wider farmhouse table can take 16 to 18.

Table runner sizes by table length

Table lengthSeats6 in drop each end9 in drop12 in drop
36 in214 × 48 in14 × 54 in14 × 60 in
48 in414 × 60 in14 × 66 in14 × 72 in
60 in4 to 614 × 72 in14 × 78 in14 × 84 in
72 in614 × 84 in14 × 90 in14 × 96 in
84 in6 to 814 × 96 in14 × 102 in14 × 108 in
96 in814 × 108 in14 × 114 in14 × 120 in

Width × length, for a 14 inch wide runner. Seats assume about 24 inches of table for each place, along both long sides. A 6 inch drop stays out of the way at the ends of the table; 12 inches is a deeper, more formal drop.

On a sideboard, a dresser or a coffee table, many runners have no drop at all and stop a few inches short of each end instead. Measure the top and take off what you want to leave showing.

Backing and binding for each runner

The top depends on the design. Backing and batting are cut 2 inches bigger than the top on every side, plenty for quilting something this small at home, and the binding is 2 1/2 inch strips cut across 42 inch fabric. These are the backing and binding calculators' answers for 14 inch wide runners.

RunnerBacking and batting to cutBacking fabricBinding
14 × 48 in18 × 52 in1 yard
2 widths seamed
4 strips
3/8 yard
14 × 60 in18 × 64 in1 yard
2 widths seamed
4 strips
3/8 yard
14 × 72 in18 × 76 in1 yard
2 widths seamed
5 strips
3/8 yard
14 × 84 in18 × 88 in1 1/2 yards
3 widths seamed
5 strips
3/8 yard
14 × 96 in18 × 100 in1 1/2 yards
3 widths seamed
6 strips
1/2 yard
14 × 108 in18 × 112 in1 1/2 yards
3 widths seamed
7 strips
1/2 yard
14 × 120 in18 × 124 in1 1/2 yards
3 widths seamed
7 strips
1/2 yard

The backing calculator cuts a runner's back across the fabric and joins the pieces end to end, because that buys the least. For a 14 × 84 runner the back is 18 × 88 inches: 3 strips 18 inches deep, cut selvage to selvage and joined, is 1 1/2 yards. One unseamed length would be 2 1/2 yards; buy that if you want a back without a seam, or a directional print running the length.

Binding is the perimeter plus 10 inches for the corners and the join: 2 × (14 + 84) + 10 = 206 inches, 5 strips. Batting is the same size as the backing. A batting package is mostly waste on a runner: half a yard off a 90 inch roll is 18 by 90 inches, enough for any 14 inch runner up to 86 inches long, and leftover batting from a bed quilt butted together with a wide zigzag works too.

Work it out for your own table

Any width, any length. Type the runner's size into the binding calculator, the backing calculator and the batting calculator, with 2 inches of overhang on the backing and batting. The fabric calculator does backing, batting and binding together.

Set a table runner size in the studio

The Size list in the studio has Baby, Lap, Throw, Twin bed, Queen bed and King bed, and no table runner preset, so you type the size. Open the setup and press Blank quilt (or pick any start), then open Quilt settings at the top of the left panel. If you want a particular block, type Block width in the Across card and Block height in the Down card first. Then type Quilt width 14 and Quilt height 84: Columns and Rows follow, and Size reads Custom. Press the lock beside a number to hold it still while you change the others. In 6 inch blocks a 14 × 84 runner is 2 by 14 blocks, with 2 inches left across for a border; in 7 inch blocks it is 2 by 12, exactly.

Step-by-step in Quiltler

More quick answers

FAQ

How long should a table runner be?

As long as the table plus 6 to 12 inches at each end. A 72 inch table takes a runner 84 to 96 inches long; a 48 inch table, 60 to 72.

How wide should a table runner be?

About a third of the table's width: 12 to 14 inches on a 36 to 42 inch wide table, up to 16 or 18 inches on a wide one.

How much binding for a 14 × 72 table runner?

5 strips of 2 1/2 inch binding cut across 42 inch fabric, 3/8 yard: the 172 inch perimeter plus 10 inches for the corners and the join.

How much backing for a table runner?

For a 14 × 84 runner, 1 1/2 yards cut into 3 strips across the fabric and joined end to end, or 2 1/2 yards for one length without a seam.

Design the quilt, then let the yardage follow

These calculators answer one question at a time. The studio counts every piece in a design, including binding, backing, and batting.

Design Online — Free Or get the companion app

Rated 4.4 stars on the App Store