Project sizes

What Size to Cut a Pillow Cover

For an envelope pillow cover, cut the front the same size as the insert, 18 × 18 inches for an 18 inch pillow form, and two back pieces 18 × 12. Sewn with a 1/2 inch seam, the cover finishes 17 × 17, an inch smaller than the insert, which is what keeps the corners full.

Squares nested on a rectangle of fabric with a leftover strip at the edge
A pillow cover is three rectangles: a front the size of the insert and two back pieces that overlap.

Envelope pillow cover cutting chart

InsertFront: cut 1Back: cut 2Finished coverFabric, 42 in wide
14 × 14 in14 × 14 in14 × 10 in13 × 13 in1/2 yard front
3/8 yard back
16 × 16 in16 × 16 in16 × 11 in15 × 15 in1/2 yard front
3/8 yard back
18 × 18 in18 × 18 in18 × 12 in17 × 17 in1/2 yard front
3/8 yard back
20 × 20 in20 × 20 in20 × 13 in19 × 19 in5/8 yard front
3/8 yard back
24 × 24 in24 × 24 in24 × 15 in23 × 23 in3/4 yard front
3/4 yard back
20 × 12 in20 × 12 in12 × 13 in19 × 11 in3/8 yard front
3/8 yard back

Width × height. Fabric is the piece calculator's yardage on 42 inch cotton, front and back counted separately so you can use two fabrics; a fat quarter (about 18 × 21) holds a 14, 16 or 18 inch front. For the 20 × 12 lumbar pillow the opening runs across the short way, so each back piece is 12 inches wide.

Why cut the front the same as the insert

A cover the same size as its insert looks flat and slack at the corners. Cut the front the size of the insert, sew it with a 1/2 inch seam, and the cover finishes an inch smaller, so the insert fills it right to the corners. Sweet Red Poppy's envelope cover chart cuts every front the same as the insert, and SewMaryMac's tutorial for Raspberry Creek Fabrics gives the same rule from the other side: make the cover smaller than the insert, about an inch smaller for a firm insert and up to two inches for a soft feather one.

For a cover that slips on loosely, or a firm foam insert you do not want to squash, cut the front 1 inch bigger than the insert instead, and the back pieces 1 inch wider.

How the envelope back is worked out

Each back piece covers half the back, plus half of the overlap, plus a hem on its open edge: half the height + 2 + 1. For an 18 inch insert that is 9 + 2 + 1 = 12 inches. The hem is 1/2 inch turned under twice and topstitched. Laid over the front with the hemmed edges overlapping, the two pieces cross by 4 inches, enough to hide the insert and hold it in.

  1. Hem one long edge of each back piece: turn under 1/2 inch, press, turn under again, press and stitch.
  2. Lay the front right side up. Lay one back piece on it right side down, raw edges level with the top, then the other level with the bottom, hems overlapping in the middle.
  3. Pin and sew all round with a 1/2 inch seam. Clip the corners, turn the cover right side out through the opening, push the corners out and put the insert in.

Quilted and pieced fronts

To quilt the front, layer the pieced top over batting and a lining an inch or two bigger all round, quilt it, then trim it to the cut size in the chart before you sew the back on. Keep points and important seams at least an inch in from the edge: the seam takes 1/2 inch, and the insert rounds the edges off a little more.

Work it out for your own pillow

Any insert. Front = the insert. Each back piece = the insert's width by half its height plus 3. The piece calculator gives the fabric for any of them.

Set a pillow size in the studio

The Size list in the studio has Baby, Lap, Throw, Twin bed, Queen bed and King bed, and no pillow preset, so you type the size. Open the setup and press Blank quilt (or pick any start), then open Quilt settings at the top of the left panel. If you want a particular block, type Block width in the Across card and Block height in the Down card first. Then type Quilt width 18 and Quilt height 18: Columns and Rows follow, and Size reads Custom. Press the lock beside a number to hold it still while you change the others. Set the quilt to the front's cut size; the outer half inch all round goes into the seam.

Step-by-step in Quiltler

More quick answers

FAQ

What size do I cut a pillow cover for an 18 inch insert?

Cut the front 18 × 18 and two back pieces 18 × 12 for an envelope cover. With a 1/2 inch seam it finishes 17 × 17, snug on the insert.

What size pillow cover for a 20 inch insert?

Cut the front 20 × 20 and two back pieces 20 × 13. The cover finishes 19 × 19. For a soft feather insert some makers go an inch smaller still.

Should a pillow cover be smaller than the insert?

Yes, by about an inch for a plump look with full corners. Cutting the front the same size as the insert and sewing a 1/2 inch seam does it.

How much do the envelope back pieces overlap?

About 4 inches. Each piece is half the height plus 2 inches of overlap and a 1 inch double hem: 16 × 11 for a 16 inch pillow.

Design the quilt, then let the yardage follow

These calculators answer one question at a time. The studio counts every piece in a design, including binding, backing, and batting.

Design Online — Free Or get the companion app

Rated 4.4 stars on the App Store