Antique Tile Quilt Block

A free cutting chart for 9", 13½" and 18" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Antique Tile is a nine-by-nine grid of grout squares with nine tile squares set in a regular three-by-three pattern, each tile ringed by grout.

  • 9 × 9 grid
  • 9", 13½" and 18" finished
  • 2 fabrics
The Antique Tile block as the Quiltler studio draws it.

What the Antique Tile block is made of

Every shape in an 18" block, by fabric, at its finished size.

FabricFinished shapes
Grout72 squares (2")
Tile9 squares (2")

The pattern sews it from 3 pieced sections (U1) and 9 strip-set segments (strip set 1).

Antique Tile cutting chart

Cut sizes for one block at 9", 13½" and 18" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

9" finished block (1" grid, 9½" unfinished)

FabricCutFor
Grout1 strip 1½" × WOF (2 half length)Strip set 1
Grout54 squares 1½"Finishes at 1" square
Tile1 strip 1½" × WOF (half length is enough)Strip set 1

13½" finished block (1½" grid, 14" unfinished)

FabricCutFor
Grout1 strip 2" × WOF (2 half length)Strip set 1
Grout54 squares 2"Finishes at 1½" square
Tile1 strip 2" × WOF (half length is enough)Strip set 1

18" finished block (2" grid, 18½" unfinished)

FabricCutFor
Grout2 strips 2½" × WOFStrip set 1
Grout54 squares 2½"Finishes at 2" square
Tile1 strip 2½" × WOFStrip set 1

How to sew an 18" Antique Tile block

Sew the strip sets

  1. Sew 3 strips together along their long edges in this order: Grout – Tile – Grout. Sew each seam in the opposite direction to the last so the set stays straight instead of bowing.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 strip set.
  4. Trim one end square, then crosscut 9 segments 2½" wide. Square the end again every few cuts.
  5. Use the segments for rows 2, 5 and 8 of unit U1.

Sew unit U1

  1. Each unit U1 takes 3 segments of strip set 1.
  2. Sew each row of the center together as the drawing shows. Press the seams in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. Each unit U1 should measure 6½" × 18½" including seam allowance. Make 3, and check the first against the drawing before making the rest.

Sew the block

  1. The block takes 3 × unit U1; make them first.
  2. Sew the 3 sections together side by side, in the order the drawing shows.
  3. The block should measure 18½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Antique Tile blocks for a quilt?

With 18" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")3 × 41254" × 72"
Queen (90" × 108")5 × 63090" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Antique Tile. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Antique Tile block FAQ

What do I cut for an 18" Antique Tile block?

For one 18" finished Antique Tile block, with a quarter-inch seam: Grout: 2 strips 2½" × WOF; 54 squares 2½". Tile: 1 strip 2½" × WOF.

How many Antique Tile blocks make a throw quilt?

At 18" finished, 3 blocks across and 4 down, 12 in all, make a 54" × 72" top with no sashing or border.

What sizes can a Antique Tile block be?

It is drafted on a 9 × 9 grid, so it works at any size that grid divides evenly. 9", 13½" and 18" give 1", 1½" and 2" squares of the grid.

Design a Antique Tile quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app