Double Four Patch Quilt Block

A free cutting chart for 6", 8" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

The Double Four Patch is four quarters on a four-by-four grid: a small four-patch in two opposite quarters, and a plain dark square the size of a whole four-patch in the other two.

  • 4 × 4 grid
  • 6", 8" and 12" finished
  • 2 fabrics
The Double Four Patch block as the Quiltler studio draws it.

What the Double Four Patch block is made of

Every shape in a 12" block, by fabric, at its finished size.

FabricFinished shapes
Light4 squares (3")
Dark2 squares (6") and 4 squares (3")

The pattern sews it from 2 four patches (U1) and 4 strip-set segments (strip set 1).

Double Four Patch cutting chart

Cut sizes for one block at 6", 8" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

6" finished block (1½" grid, 6½" unfinished)

FabricCutFor
Light1 strip 2" × WOF (half length is enough)Strip set 1
Dark1 strip 2" × WOF (half length is enough)Strip set 1
Dark2 squares 3½"Finishes at 3" square

8" finished block (2" grid, 8½" unfinished)

FabricCutFor
Light1 strip 2½" × WOF (half length is enough)Strip set 1
Dark1 strip 2½" × WOF (half length is enough)Strip set 1
Dark2 squares 4½"Finishes at 4" square

12" finished block (3" grid, 12½" unfinished)

FabricCutFor
Light1 strip 3½" × WOF (half length is enough)Strip set 1
Dark1 strip 3½" × WOF (half length is enough)Strip set 1
Dark2 squares 6½"Finishes at 6" square

How to sew a 12" Double Four Patch block

Sew the strip sets

  1. Sew 2 strips together along their long edges in this order: Dark – Light.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 half-length set from strips cut in half.
  4. Trim one end square, then crosscut 4 segments 3½" wide. Square the end again every few cuts.
  5. Use the segments for rows 1 and 2 of unit U1.
  6. Where a row reads the other way round, turn the segment end for end before sewing it in.

Sew unit U1 (four patch)

  1. Each unit U1 takes 2 segments of strip set 1.
  2. Lay the segments out as the drawing shows, turning the segment in row 2 end for end.
  3. Join the rows, matching the seams where they meet.
  4. Each unit U1 should measure 6½" square including seam allowance. Make 2, and check the first against the drawing before making the rest.

Sew the block

  1. The block takes 2 × unit U1; make them first.
  2. Lay the sections out as the drawing shows, 2 rows of 2. Sew the sections of each row together, pressing the seams in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Double Four Patch blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Double Four Patch. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Double Four Patch block FAQ

What do I cut for a 12" Double Four Patch block?

For one 12" finished Double Four Patch block, with a quarter-inch seam: Light: 1 strip 3½" × WOF (half length is enough). Dark: 1 strip 3½" × WOF (half length is enough); 2 squares 6½".

How many Double Four Patch blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Double Four Patch block be?

It is drafted on a 4 × 4 grid, so it works at any size that grid divides evenly. 6", 8" and 12" give 1½", 2" and 3" squares of the grid.

Design a Double Four Patch quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app