Octagon is one large square with its four corners covered by small triangles, so the center reads as an eight-sided shape. It is sewn like a Snowball, corners stitched and flipped, but each corner triangle is a quarter of the block's width rather than a third.
- 4 × 4 grid
- 6", 8" and 12" finished
- 2 fabrics
On this page
What the Octagon block is made of
Every shape in a 12" block, by fabric, at its finished size. Where a triangle sits on the corner of a square, the square is listed whole: it is cut whole and the corner sewn on top, stitch and flip.
| Fabric | Finished shapes |
|---|---|
| Corners | 4 half-square triangles (3") |
| Center | 1 square (12") |
The pattern sews it from 1 stitch-and-flip corner unit (S1).
Octagon cutting chart
Cut sizes for one block at 6", 8" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.
6" finished block (1½" grid, 6½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Corners | 4 squares 2" | S1: stitch-and-flip corners |
| Center | 1 square 6½" | S1: stitch-and-flip corners |
8" finished block (2" grid, 8½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Corners | 4 squares 2½" | S1: stitch-and-flip corners |
| Center | 1 square 8½" | S1: stitch-and-flip corners |
12" finished block (3" grid, 12½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Corners | 4 squares 3½" | S1: stitch-and-flip corners |
| Center | 1 square 12½" | S1: stitch-and-flip corners |
How to sew a 12" Octagon block
Make the units
- Draw a line corner to corner on the back of each corner square: 4 × Corners 3½" square for each unit.
- Lay each square on its corner of a Center piece, 12½" square, right sides together as the drawing shows, and sew on the line.
- Trim a quarter inch outside the seam and press the corner out. Make 1 unit.
Sew the block
- The block takes 1 × S1; make it first.
- The block should measure 12½" square including seam allowance. Check it against the drawing.
Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.
How many Octagon blocks for a quilt?
With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:
| Quilt | Blocks across × down | Blocks | Finished top |
|---|---|---|---|
| Throw (60" × 72") | 5 × 6 | 30 | 60" × 72" |
| Queen (90" × 108") | 8 × 9 | 72 | 96" × 108" |
Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.
Design with this block
Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Octagon. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.
The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library
Related blocks
Bow Tie
Cutting chart, sizes and sewing steps.
Steps to the Altar
Cutting chart, sizes and sewing steps.
Arrow
Cutting chart, sizes and sewing steps.
Union Square
Cutting chart, sizes and sewing steps.
Every classic block in the studio is in the quilt block library.