Jacob's Ladder is a three-by-three block of five four-patches and four half-square triangles. The four-patches sit in the corners and the center, so their dark squares step corner to corner across the block, and the triangles fill the sides.
- 6 × 6 grid
- 6", 9" and 12" finished
- 2 fabrics
On this page
What the Jacob's Ladder block is made of
Every shape in a 12" block, by fabric, at its finished size.
| Fabric | Finished shapes |
|---|---|
| Light | 4 half-square triangles (4") and 10 squares (2") |
| Dark | 4 half-square triangles (4") and 10 squares (2") |
The pattern sews it from 5 four patches (U1), 10 strip-set segments (strip set 1) and 4 half-square triangle units (H1).
It goes together in 3 rows of 3: 5 four-patches and 4 half-square triangles.
Jacob's Ladder cutting chart
Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.
WOF is the width of the fabric, 42" after the selvages are trimmed.
6" finished block (1" grid, 6½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Light | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Light | 2 squares 2⅞" | H1: half-square triangles, two at a time |
| Dark | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Dark | 2 squares 2⅞" | H1: half-square triangles, two at a time |
9" finished block (1½" grid, 9½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Light | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Light | 2 squares 3⅞" | H1: half-square triangles, two at a time |
| Dark | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Dark | 2 squares 3⅞" | H1: half-square triangles, two at a time |
12" finished block (2" grid, 12½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Light | 1 strip 2½" × WOF | Strip set 1 |
| Light | 2 squares 4⅞" | H1: half-square triangles, two at a time |
| Dark | 1 strip 2½" × WOF | Strip set 1 |
| Dark | 2 squares 4⅞" | H1: half-square triangles, two at a time |
How to sew a 12" Jacob's Ladder block
Make the units
- Pair each Dark square with a Light square, 4⅞" square, right sides together. Draw a line corner to corner on the back of the lighter one.
- Sew a quarter inch either side of the line, cut on the line and press open. Each pair makes two units.
- Make 4 units from 2 pairs. Each should measure 4½" square with seam allowance.
Sew the strip sets
- Sew 2 strips together along their long edges in this order: Dark – Light.
- Press every seam to one side, toward the darker fabric where you can.
- Make 1 strip set.
- Trim one end square, then crosscut 10 segments 2½" wide. Square the end again every few cuts.
- Use the segments for rows 1 and 2 of unit U1.
- Where a row reads the other way round, turn the segment end for end before sewing it in.
Sew unit U1 (four patch)
- Each unit U1 takes 2 segments of strip set 1.
- Row 1 is a segment of strip set 1, sewn and pressed with the set.
- Row 2 is a segment of strip set 1, turned end for end, sewn and pressed with the set.
- Join the rows, nesting the seams where they meet, then press the seam open.
- Each unit U1 should measure 4½" square including seam allowance. Make 5, and check the first against the drawing before making the rest.
Sew the block
- The block takes 5 × unit U1 and 4 × H1; make them first.
- Lay out the units in 3 rows of 3 as the drawing shows.
- Rows 1 and 3: sew four-patch (unit U1), half-square triangle (H1) and four-patch (unit U1) together, then press the seams toward the four-patches.
- Row 2: sew half-square triangle (H1), four-patch (unit U1) and half-square triangle (H1) together, then press the seams toward the four-patch.
- Join the rows, nesting the seams where they meet, then press the seams toward the middle row.
- The block should measure 12½" square including seam allowance. Check it against the drawing.
Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.
How many Jacob's Ladder blocks for a quilt?
With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:
| Quilt | Blocks across × down | Blocks | Finished top |
|---|---|---|---|
| Throw (60" × 72") | 5 × 6 | 30 | 60" × 72" |
| Queen (90" × 108") | 8 × 9 | 72 | 96" × 108" |
Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.
Design with this block
Start a throw-size Jacob's Ladder quilt in the studio and recolor it in your own fabrics. To add the block to any other quilt, open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Jacob's Ladder. Click the block, then click a space on the quilt.
The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library
Related blocks
Garden of Eden
Cutting chart, sizes and sewing steps.
Next Door Neighbor
Cutting chart, sizes and sewing steps.
California
Cutting chart, sizes and sewing steps.
Grandmother's Choice
Cutting chart, sizes and sewing steps.
Every classic block in the studio is in the quilt block library.