Chimney Sweep Quilt Block

A free cutting chart for 6", 9" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Chimney Sweep is a six-by-six block in a three-by-three layout: a four-patch in each corner, plain background squares on the sides and a plain accent square in the center, so the accent runs from each corner into the middle in an X.

  • 6 × 6 grid
  • 6", 9" and 12" finished
  • 2 fabrics
The Chimney Sweep block as the Quiltler studio draws it.

What the Chimney Sweep block is made of

Every shape in a 12" block, by fabric, at its finished size.

FabricFinished shapes
Background4 squares (4") and 8 squares (2")
Accent1 square (4") and 8 squares (2")

The pattern sews it from 4 four patches (U1) and 8 strip-set segments (strip set 1).

Chimney Sweep cutting chart

Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

6" finished block (1" grid, 6½" unfinished)

FabricCutFor
Background1 strip 1½" × WOF (half length is enough)Strip set 1
Background4 squares 2½"Finishes at 2" square
Accent1 strip 1½" × WOF (half length is enough)Strip set 1
Accent1 square 2½"Finishes at 2" square

9" finished block (1½" grid, 9½" unfinished)

FabricCutFor
Background1 strip 2" × WOF (half length is enough)Strip set 1
Background4 squares 3½"Finishes at 3" square
Accent1 strip 2" × WOF (half length is enough)Strip set 1
Accent1 square 3½"Finishes at 3" square

12" finished block (2" grid, 12½" unfinished)

FabricCutFor
Background1 strip 2½" × WOF (half length is enough)Strip set 1
Background4 squares 4½"Finishes at 4" square
Accent1 strip 2½" × WOF (half length is enough)Strip set 1
Accent1 square 4½"Finishes at 4" square

How to sew a 12" Chimney Sweep block

Sew the strip sets

  1. Sew 2 strips together along their long edges in this order: Accent – Background.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 half-length set from strips cut in half.
  4. Trim one end square, then crosscut 8 segments 2½" wide. Square the end again every few cuts.
  5. Use the segments for rows 1 and 2 of unit U1.
  6. Where a row reads the other way round, turn the segment end for end before sewing it in.

Sew unit U1 (four patch)

  1. Each unit U1 takes 2 segments of strip set 1.
  2. Lay the segments out as the drawing shows, turning the segment in row 2 end for end.
  3. Join the rows, matching the seams where they meet.
  4. Each unit U1 should measure 4½" square including seam allowance. Make 4, and check the first against the drawing before making the rest.

Sew the block

  1. The block takes 4 × unit U1; make them first.
  2. Lay the sections out as the drawing shows, 3 rows of 3. Sew the sections of each row together, pressing the seams in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Chimney Sweep blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Chimney Sweep. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Chimney Sweep block FAQ

What do I cut for a 12" Chimney Sweep block?

For one 12" finished Chimney Sweep block, with a quarter-inch seam: Background: 1 strip 2½" × WOF (half length is enough); 4 squares 4½". Accent: 1 strip 2½" × WOF (half length is enough); 1 square 4½".

How many Chimney Sweep blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Chimney Sweep block be?

It is drafted on a 6 × 6 grid, so it works at any size that grid divides evenly. 6", 9" and 12" give 1", 1½" and 2" squares of the grid.

Design a Chimney Sweep quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app