Double Nine Patch Quilt Block

A free cutting chart for 9", 13½" and 18" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

The Double Nine Patch is a nine patch made of nine patches: on a nine-by-nine grid, five small nine-patches, in the corners and the center, alternate with four areas of plain light squares the same size.

  • 9 × 9 grid
  • 9", 13½" and 18" finished
  • 2 fabrics
The Double Nine Patch block as the Quiltler studio draws it.

What the Double Nine Patch block is made of

Every shape in an 18" block, by fabric, at its finished size.

FabricFinished shapes
Light56 squares (2")
Dark25 squares (2")

The pattern sews it from 4 strip-set segments (strip set 1).

Double Nine Patch cutting chart

Cut sizes for one block at 9", 13½" and 18" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

9" finished block (1" grid, 9½" unfinished)

FabricCutFor
Light1 strip 3½" × WOF (half length is enough)Strip set 1
Light1 strip 1½" × WOF (2 half length)Strip set 1
Light36 squares 1½"Finishes at 1" square
Dark2 strips 1½" × WOF (4 half length)Strip set 1
Dark9 squares 1½"Finishes at 1" square

13½" finished block (1½" grid, 14" unfinished)

FabricCutFor
Light1 strip 5" × WOF (half length is enough)Strip set 1
Light1 strip 2" × WOF (2 half length)Strip set 1
Light36 squares 2"Finishes at 1½" square
Dark2 strips 2" × WOF (4 half length)Strip set 1
Dark9 squares 2"Finishes at 1½" square

18" finished block (2" grid, 18½" unfinished)

FabricCutFor
Light1 strip 6½" × WOF (half length is enough)Strip set 1
Light1 strip 2½" × WOF (2 half length)Strip set 1
Light36 squares 2½"Finishes at 2" square
Dark2 strips 2½" × WOF (4 half length)Strip set 1
Dark9 squares 2½"Finishes at 2" square

How to sew an 18" Double Nine Patch block

Sew the strip sets

  1. Sew 7 strips together along their long edges in this order: Dark – Light – Dark – Light – Dark – Light – Dark. Sew each seam in the opposite direction to the last so the set stays straight instead of bowing.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 half-length set from strips cut in half.
  4. Trim one end square, then crosscut 4 segments 2½" wide. Square the end again every few cuts.
  5. Use the segments for rows 1, 3, 7 and 9 of the block.

Sew the block

  1. The block takes 4 segments of strip set 1.
  2. Sew each row of the center together as the drawing shows. Press the seams in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. The block should measure 18½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Double Nine Patch blocks for a quilt?

With 18" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")3 × 41254" × 72"
Queen (90" × 108")5 × 63090" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Double Nine Patch. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Double Nine Patch block FAQ

What do I cut for an 18" Double Nine Patch block?

For one 18" finished Double Nine Patch block, with a quarter-inch seam: Light: 1 strip 6½" × WOF (half length is enough); 1 strip 2½" × WOF (2 half length); 36 squares 2½". Dark: 2 strips 2½" × WOF (4 half length); 9 squares 2½".

How many Double Nine Patch blocks make a throw quilt?

At 18" finished, 3 blocks across and 4 down, 12 in all, make a 54" × 72" top with no sashing or border.

What sizes can a Double Nine Patch block be?

It is drafted on a 9 × 9 grid, so it works at any size that grid divides evenly. 9", 13½" and 18" give 1", 1½" and 2" squares of the grid.

Design a Double Nine Patch quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app