Churn Dash is a three-by-three block: a half-square triangle in each corner, a two-strip rail on each side, and a plain center square. It also goes by Monkey Wrench and Hole in the Barn Door.
- 6 × 6 grid
- 6", 9" and 12" finished
- 2 fabrics
- Also called Monkey Wrench and Hole in the Barn Door
On this page
What the Churn Dash block is made of
Every shape in a 12" block, by fabric, at its finished size.
| Fabric | Finished shapes |
|---|---|
| Background | 1 square (4"), 4 half-square triangles (4") and 4 rectangles (4" × 2") |
| Accent | 4 half-square triangles (4") and 4 rectangles (4" × 2") |
The pattern sews it from 4 half-square triangle units (H1) and 4 strip-set segments (strip set 1).
It goes together in 3 rows of 3: 4 half-square triangles, 4 rails and 1 center square.
Churn Dash cutting chart
Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.
WOF is the width of the fabric, 42" after the selvages are trimmed.
6" finished block (1" grid, 6½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Background | 2 squares 2⅞" | H1: half-square triangles, two at a time |
| Background | 1 square 2½" | Finishes at 2" square |
| Accent | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Accent | 2 squares 2⅞" | H1: half-square triangles, two at a time |
9" finished block (1½" grid, 9½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Background | 2 squares 3⅞" | H1: half-square triangles, two at a time |
| Background | 1 square 3½" | Finishes at 3" square |
| Accent | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Accent | 2 squares 3⅞" | H1: half-square triangles, two at a time |
12" finished block (2" grid, 12½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 2½" × WOF (half length is enough) | Strip set 1 |
| Background | 2 squares 4⅞" | H1: half-square triangles, two at a time |
| Background | 1 square 4½" | Finishes at 4" square |
| Accent | 1 strip 2½" × WOF (half length is enough) | Strip set 1 |
| Accent | 2 squares 4⅞" | H1: half-square triangles, two at a time |
How to sew a 12" Churn Dash block
Make the units
- Pair each Accent square with a Background square, 4⅞" square, right sides together. Draw a line corner to corner on the back of the lighter one.
- Sew a quarter inch either side of the line, cut on the line and press open. Each pair makes two units.
- Make 4 units from 2 pairs. Each should measure 4½" square with seam allowance.
Sew the strip sets
- Sew 2 strips together along their long edges in this order: Accent – Background.
- Press every seam to one side, toward the darker fabric where you can.
- Make 1 half-length set from strips cut in half.
- Trim one end square, then crosscut 4 segments 4½" wide. Square the end again every few cuts.
- Use the segments for rows 1, 2 and 3 of the block.
- Where a row reads the other way round, turn the segment end for end before sewing it in.
Sew the block
- The block takes 4 × H1; make them first.
- The block takes 4 segments of strip set 1.
- Lay out the units, segments and pieces in 3 rows of 3 as the drawing shows, each one turned the way it lies there.
- Rows 1 and 3: sew half-square triangle (H1), rail (strip set 1) and half-square triangle (H1) together, then press the seams toward the rail.
- Row 2: sew rail (strip set 1), center square (Background) and rail (strip set 1) together, then press the seams toward the rails.
- Join the rows, nesting the seams where they meet, then press the seams toward the middle row.
- The block should measure 12½" square including seam allowance. Check it against the drawing.
Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.
How many Churn Dash blocks for a quilt?
With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:
| Quilt | Blocks across × down | Blocks | Finished top |
|---|---|---|---|
| Throw (60" × 72") | 5 × 6 | 30 | 60" × 72" |
| Queen (90" × 108") | 8 × 9 | 72 | 96" × 108" |
Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.
Design with this block
Start a throw-size Churn Dash quilt in the studio and recolor it in your own fabrics. To add the block to any other quilt, open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Churn Dash. Click the block, then click a space on the quilt.
The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library
Related blocks
Rolling Stone
Cutting chart, sizes and sewing steps.
Grandmother's Choice
Cutting chart, sizes and sewing steps.
Jack in the Box
Cutting chart, sizes and sewing steps.
Swing in the Center
Cutting chart, sizes and sewing steps.
Every classic block in the studio is in the quilt block library.