Burgoyne Surrounded Quilt Block

A free cutting chart for 9", 13½" and 18" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Burgoyne Surrounded is drafted on a nine-by-nine grid of small squares: a small nine-patch in each corner, a solid square of army fabric three squares across in the center, and a line one square wide running from it to the middle of each edge.

  • 9 × 9 grid
  • 9", 13½" and 18" finished
  • 2 fabrics
The Burgoyne Surrounded block as the Quiltler studio draws it.

What the Burgoyne Surrounded block is made of

Every shape in an 18" block, by fabric, at its finished size.

FabricFinished shapes
Background40 squares (2")
Army41 squares (2")

The pattern sews it from 2 pieced sections (U1), 24 strip-set segments (strip set 1, strip set 1, strip set 2) and 1 pieced section (U2).

Burgoyne Surrounded cutting chart

Cut sizes for one block at 9", 13½" and 18" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

9" finished block (1" grid, 9½" unfinished)

FabricCutFor
Background3 strips 1½" × WOF (1 half length)Strip set 1 and 2
Army2 strips 1½" × WOF (half length is enough)Strip set 1 and 2
Army9 squares 1½"Finishes at 1" square

13½" finished block (1½" grid, 14" unfinished)

FabricCutFor
Background3 strips 2" × WOF (1 half length)Strip set 1 and 2
Army2 strips 2" × WOF (half length is enough)Strip set 1 and 2
Army9 squares 2"Finishes at 1½" square

18" finished block (2" grid, 18½" unfinished)

FabricCutFor
Background3 strips 2½" × WOF (1 half length)Strip set 1 and 2
Army2 strips 2½" × WOF (half length is enough)Strip set 1 and 2
Army9 squares 2½"Finishes at 2" square

How to sew an 18" Burgoyne Surrounded block

Sew the strip sets

  1. Sew 3 strips together along their long edges in this order: Background – Army – Background. Sew each seam in the opposite direction to the last so the set stays straight instead of bowing.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 strip set.
  4. Trim one end square, then crosscut 16 segments 2½" wide. Square the end again every few cuts.
  5. Use the segments for rows 1, 2, 3, 7, 8 and 9 of unit U2; rows 1, 2 and 3 of unit U1.
  6. Sew 3 strips together along their long edges in this order: Army – Background – Army. Sew each seam in the opposite direction to the last so the set stays straight instead of bowing.
  7. Press every seam to one side, toward the darker fabric where you can.
  8. Make 1 half-length set from strips cut in half.
  9. Trim one end square, then crosscut 8 segments 2½" wide. Square the end again every few cuts.
  10. Use the segments for rows 1 and 3 of unit U1.

Sew unit U1

  1. Each unit U1 takes 4 segments of strip set 2 and 5 segments of strip set 1.
  2. Sew each row of Unit U1 together left to right, as the drawing shows. Press the seam allowances in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. Each unit U1 should measure 6½" × 18½" including seam allowance. Make 2, and check the first against the drawing before making the rest.

Sew unit U2

  1. Unit U2 takes 6 segments of strip set 1.
  2. Sew each row of the center together as the drawing shows. Press the seams in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. Each unit U2 should measure 6½" × 18½" including seam allowance. Check it against the drawing.

Sew the block

  1. The block takes 2 × unit U1 and 1 × unit U2; make them first.
  2. Sew the 3 sections together side by side, in the order the drawing shows.
  3. The block should measure 18½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Burgoyne Surrounded blocks for a quilt?

With 18" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")3 × 41254" × 72"
Queen (90" × 108")5 × 63090" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Burgoyne Surrounded. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Burgoyne Surrounded block FAQ

What do I cut for an 18" Burgoyne Surrounded block?

For one 18" finished Burgoyne Surrounded block, with a quarter-inch seam: Background: 3 strips 2½" × WOF (1 half length). Army: 2 strips 2½" × WOF (half length is enough); 9 squares 2½".

How many Burgoyne Surrounded blocks make a throw quilt?

At 18" finished, 3 blocks across and 4 down, 12 in all, make a 54" × 72" top with no sashing or border.

What sizes can a Burgoyne Surrounded block be?

It is drafted on a 9 × 9 grid, so it works at any size that grid divides evenly. 9", 13½" and 18" give 1", 1½" and 2" squares of the grid.

Design a Burgoyne Surrounded quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app