Quiltler's Double Wrench is a six-by-six block in a three-by-three layout: a four-patch in each corner, a two-rectangle unit on each side with the accent on the outer edge, and a plain background square in the center.
- 6 × 6 grid
- 6", 9" and 12" finished
- 2 fabrics
On this page
What the Double Wrench block is made of
Every shape in a 12" block, by fabric, at its finished size.
| Fabric | Finished shapes |
|---|---|
| Background | 1 square (4"), 4 rectangles (4" × 2") and 8 squares (2") |
| Accent | 4 rectangles (4" × 2") and 8 squares (2") |
The pattern sews it from 2 pieced sections (U1), 8 strip-set segments (strip set 1) and 1 pieced section (U2).
Double Wrench cutting chart
Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.
WOF is the width of the fabric, 42" after the selvages are trimmed.
6" finished block (1" grid, 6½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Background | 1 square 2½" | Finishes at 2" square |
| Background | 4 rectangles 2½" × 1½" | Finishes at 2" × 1" |
| Accent | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Accent | 4 rectangles 2½" × 1½" | Finishes at 2" × 1" |
9" finished block (1½" grid, 9½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Background | 1 square 3½" | Finishes at 3" square |
| Background | 4 rectangles 3½" × 2" | Finishes at 3" × 1½" |
| Accent | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Accent | 4 rectangles 3½" × 2" | Finishes at 3" × 1½" |
12" finished block (2" grid, 12½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 2½" × WOF (half length is enough) | Strip set 1 |
| Background | 1 square 4½" | Finishes at 4" square |
| Background | 4 rectangles 4½" × 2½" | Finishes at 4" × 2" |
| Accent | 1 strip 2½" × WOF (half length is enough) | Strip set 1 |
| Accent | 4 rectangles 4½" × 2½" | Finishes at 4" × 2" |
How to sew a 12" Double Wrench block
Sew the strip sets
- Sew 2 strips together along their long edges in this order: Accent – Background.
- Press every seam to one side, toward the darker fabric where you can.
- Make 1 half-length set from strips cut in half.
- Trim one end square, then crosscut 8 segments 2½" wide. Square the end again every few cuts.
- Use the segments for rows 1, 2, 4 and 5 of unit U1.
- Where a row reads the other way round, turn the segment end for end before sewing it in.
Sew unit U1
- Each unit U1 takes 4 segments of strip set 1.
- Sew each row of the center together as the drawing shows. Press the seams in alternate directions row to row so they nest.
- Join the rows, matching the seams where they meet.
- Each unit U1 should measure 4½" × 12½" including seam allowance. Make 2, and check the first against the drawing before making the rest.
Sew unit U2
- Sew the 5 pieces of Unit U2 together top to bottom, as the drawing shows.
- Each unit U2 should measure 4½" × 12½" including seam allowance. Check it against the drawing.
Sew the block
- The block takes 2 × unit U1 and 1 × unit U2; make them first.
- Sew the 3 sections together side by side, in the order the drawing shows.
- The block should measure 12½" square including seam allowance. Check it against the drawing.
Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.
How many Double Wrench blocks for a quilt?
With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:
| Quilt | Blocks across × down | Blocks | Finished top |
|---|---|---|---|
| Throw (60" × 72") | 5 × 6 | 30 | 60" × 72" |
| Queen (90" × 108") | 8 × 9 | 72 | 96" × 108" |
Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.
Design with this block
Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Double Wrench. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.
The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library
Related blocks
Disappearing Nine Patch
Cutting chart, sizes and sewing steps.
Barrister's Block
Cutting chart, sizes and sewing steps.
Prairie Queen
Cutting chart, sizes and sewing steps.
Chimney Sweep
Cutting chart, sizes and sewing steps.
Every classic block in the studio is in the quilt block library.