Rolling Stone Quilt Block

A free cutting chart for 6", 9" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Rolling Stone is a six-by-six block in a three-by-three layout: a plain stone square in the center, a two-rectangle unit on each side with the stone fabric on the outer edge, and a square-in-a-square in each corner, a stone square set on point.

  • 6 × 6 grid
  • 6", 9" and 12" finished
  • 2 fabrics
The Rolling Stone block as the Quiltler studio draws it.

What the Rolling Stone block is made of

Every shape in a 12" block, by fabric, at its finished size. Where a triangle sits on the corner of a square, the square is listed whole: it is cut whole and the corner sewn on top, stitch and flip.

FabricFinished shapes
Background4 rectangles (4" × 2") and 16 half-square triangles (2")
Stone5 squares (4") and 4 rectangles (4" × 2")

The pattern sews it from 4 stitch-and-flip corner units (S1) and 4 strip-set segments (strip set 1).

Rolling Stone cutting chart

Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

WOF is the width of the fabric, 42" after the selvages are trimmed.

6" finished block (1" grid, 6½" unfinished)

FabricCutFor
Background1 strip 1½" × WOF (half length is enough)Strip set 1
Background16 squares 1½"S1: stitch-and-flip corners
Stone1 strip 1½" × WOF (half length is enough)Strip set 1
Stone1 square 2½"Finishes at 2" square
Stone4 squares 2½"S1: stitch-and-flip corners

9" finished block (1½" grid, 9½" unfinished)

FabricCutFor
Background1 strip 2" × WOF (half length is enough)Strip set 1
Background16 squares 2"S1: stitch-and-flip corners
Stone1 strip 2" × WOF (half length is enough)Strip set 1
Stone1 square 3½"Finishes at 3" square
Stone4 squares 3½"S1: stitch-and-flip corners

12" finished block (2" grid, 12½" unfinished)

FabricCutFor
Background1 strip 2½" × WOF (half length is enough)Strip set 1
Background16 squares 2½"S1: stitch-and-flip corners
Stone1 strip 2½" × WOF (half length is enough)Strip set 1
Stone1 square 4½"Finishes at 4" square
Stone4 squares 4½"S1: stitch-and-flip corners

How to sew a 12" Rolling Stone block

Make the units

  1. Draw a line corner to corner on the back of each corner square: 4 × Background 2½" square for each unit.
  2. Lay one square on its corner of a Stone piece, 4½" square, right sides together as the drawing shows, and sew on the line. Trim a quarter inch outside the seam and press the corner out, then sew, trim and press each of the other 3 squares in turn the same way: the squares overlap, so they go on one at a time.
  3. Make 4 units this way.

Sew the strip sets

  1. Sew 2 strips together along their long edges in this order: Stone – Background.
  2. Press every seam to one side, toward the darker fabric where you can.
  3. Make 1 half-length set from strips cut in half.
  4. Trim one end square, then crosscut 4 segments 4½" wide. Square the end again every few cuts.
  5. Use the segments for rows 1, 2 and 3 of the block.
  6. Where a row reads the other way round, turn the segment end for end before sewing it in.

Sew the block

  1. The block takes 4 × S1; make them first.
  2. The block takes 4 segments of strip set 1.
  3. Sew each row of the block together left to right, as the drawing shows. Press the seam allowances in alternate directions row to row so they nest.
  4. Join the rows, matching the seams where they meet.
  5. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Rolling Stone blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Rolling Stone. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Rolling Stone block FAQ

What do I cut for a 12" Rolling Stone block?

For one 12" finished Rolling Stone block, with a quarter-inch seam: Background: 1 strip 2½" × WOF (half length is enough); 16 squares 2½". Stone: 1 strip 2½" × WOF (half length is enough); 1 square 4½"; 4 squares 4½".

How many Rolling Stone blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Rolling Stone block be?

It is drafted on a 6 × 6 grid, so it works at any size that grid divides evenly. 6", 9" and 12" give 1", 1½" and 2" squares of the grid.

Design a Rolling Stone quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app