Hartford is a six-by-six block in a three-by-three layout: a four-patch in each corner, a two-rectangle unit on each side with the accent on the outer edge, and a square-in-a-square in the center, an accent square set on point.
- 6 × 6 grid
- 6", 9" and 12" finished
- 2 fabrics
On this page
What the Hartford block is made of
Every shape in a 12" block, by fabric, at its finished size. Where a triangle sits on the corner of a square, the square is listed whole: it is cut whole and the corner sewn on top, stitch and flip.
| Fabric | Finished shapes |
|---|---|
| Background | 4 rectangles (4" × 2"), 8 squares (2") and 4 half-square triangles (2") |
| Accent | 1 square (4"), 4 rectangles (4" × 2") and 8 squares (2") |
The pattern sews it from 2 pieced sections (U1), 8 strip-set segments (strip set 1), 1 pieced section (U2) and 1 stitch-and-flip corner unit (S1).
Hartford cutting chart
Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.
WOF is the width of the fabric, 42" after the selvages are trimmed.
6" finished block (1" grid, 6½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Background | 4 rectangles 2½" × 1½" | Finishes at 2" × 1" |
| Background | 4 squares 1½" | S1: stitch-and-flip corners |
| Accent | 1 strip 1½" × WOF (half length is enough) | Strip set 1 |
| Accent | 1 square 2½" | S1: stitch-and-flip corners |
| Accent | 4 rectangles 2½" × 1½" | Finishes at 2" × 1" |
9" finished block (1½" grid, 9½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Background | 4 rectangles 3½" × 2" | Finishes at 3" × 1½" |
| Background | 4 squares 2" | S1: stitch-and-flip corners |
| Accent | 1 strip 2" × WOF (half length is enough) | Strip set 1 |
| Accent | 1 square 3½" | S1: stitch-and-flip corners |
| Accent | 4 rectangles 3½" × 2" | Finishes at 3" × 1½" |
12" finished block (2" grid, 12½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Background | 1 strip 2½" × WOF (half length is enough) | Strip set 1 |
| Background | 4 rectangles 4½" × 2½" | Finishes at 4" × 2" |
| Background | 4 squares 2½" | S1: stitch-and-flip corners |
| Accent | 1 strip 2½" × WOF (half length is enough) | Strip set 1 |
| Accent | 1 square 4½" | S1: stitch-and-flip corners |
| Accent | 4 rectangles 4½" × 2½" | Finishes at 4" × 2" |
How to sew a 12" Hartford block
Make the units
- Draw a line corner to corner on the back of each corner square: 4 × Background 2½" square for each unit.
- Lay one square on its corner of an Accent piece, 4½" square, right sides together as the drawing shows, and sew on the line. Trim a quarter inch outside the seam and press the corner out, then sew, trim and press each of the other 3 squares in turn the same way: the squares overlap, so they go on one at a time.
- Make 1 unit this way.
Sew the strip sets
- Sew 2 strips together along their long edges in this order: Accent – Background.
- Press every seam to one side, toward the darker fabric where you can.
- Make 1 half-length set from strips cut in half.
- Trim one end square, then crosscut 8 segments 2½" wide. Square the end again every few cuts.
- Use the segments for rows 1, 2, 4 and 5 of unit U1.
- Where a row reads the other way round, turn the segment end for end before sewing it in.
Sew unit U1
- Each unit U1 takes 4 segments of strip set 1.
- Sew each row of the center together as the drawing shows. Press the seams in alternate directions row to row so they nest.
- Join the rows, matching the seams where they meet.
- Each unit U1 should measure 4½" × 12½" including seam allowance. Make 2, and check the first against the drawing before making the rest.
Sew unit U2
- Unit U2 takes 1 × S1; make it first.
- Sew the 5 pieces of Unit U2 together top to bottom, as the drawing shows.
- Each unit U2 should measure 4½" × 12½" including seam allowance. Check it against the drawing.
Sew the block
- The block takes 2 × unit U1 and 1 × unit U2; make them first.
- Sew the 3 sections together side by side, in the order the drawing shows.
- The block should measure 12½" square including seam allowance. Check it against the drawing.
Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.
How many Hartford blocks for a quilt?
With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:
| Quilt | Blocks across × down | Blocks | Finished top |
|---|---|---|---|
| Throw (60" × 72") | 5 × 6 | 30 | 60" × 72" |
| Queen (90" × 108") | 8 × 9 | 72 | 96" × 108" |
Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.
Design with this block
Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Hartford. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.
The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library
Related blocks
Rolling Stone
Cutting chart, sizes and sewing steps.
Churn Dash
Cutting chart, sizes and sewing steps.
Grandmother's Choice
Cutting chart, sizes and sewing steps.
Jack in the Box
Cutting chart, sizes and sewing steps.
Every classic block in the studio is in the quilt block library.