Checkerboard is thirty-six squares in six rows of six, light and dark alternating. It is pieced from one strip set of six strips, light and dark alternating, cut into segments with every other one turned end for end.
- 6 × 6 grid
- 6", 9" and 12" finished
- 2 fabrics
On this page
What the Checkerboard block is made of
Every shape in a 12" block, by fabric, at its finished size.
| Fabric | Finished shapes |
|---|---|
| Light | 18 squares (2") |
| Dark | 18 squares (2") |
The pattern sews it from 6 strip-set segments (strip set 1).
Checkerboard cutting chart
Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.
WOF is the width of the fabric, 42" after the selvages are trimmed.
6" finished block (1" grid, 6½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Light | 2 strips 1½" × WOF (3 half length) | Strip set 1 |
| Dark | 2 strips 1½" × WOF (3 half length) | Strip set 1 |
9" finished block (1½" grid, 9½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Light | 2 strips 2" × WOF (3 half length) | Strip set 1 |
| Dark | 2 strips 2" × WOF (3 half length) | Strip set 1 |
12" finished block (2" grid, 12½" unfinished)
| Fabric | Cut | For |
|---|---|---|
| Light | 2 strips 2½" × WOF (3 half length) | Strip set 1 |
| Dark | 2 strips 2½" × WOF (3 half length) | Strip set 1 |
How to sew a 12" Checkerboard block
Sew the strip sets
- Sew 6 strips together along their long edges in this order: Dark – Light – Dark – Light – Dark – Light. Sew each seam in the opposite direction to the last so the set stays straight instead of bowing.
- Press every seam to one side, toward the darker fabric where you can.
- Make 1 half-length set from strips cut in half.
- Trim one end square, then crosscut 6 segments 2½" wide. Square the end again every few cuts.
- Use the segments for rows 1, 2, 3, 4, 5 and 6 of the block.
- Where a row reads the other way round, turn the segment end for end before sewing it in.
Sew the block
- The block takes 6 segments of strip set 1.
- Lay the segments out as the drawing shows, turning the segments in rows 2, 4 and 6 end for end.
- Join the rows, matching the seams where they meet.
- The block should measure 12½" square including seam allowance. Check it against the drawing.
Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.
How many Checkerboard blocks for a quilt?
With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:
| Quilt | Blocks across × down | Blocks | Finished top |
|---|---|---|---|
| Throw (60" × 72") | 5 × 6 | 30 | 60" × 72" |
| Queen (90" × 108") | 8 × 9 | 72 | 96" × 108" |
Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.
Design with this block
Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Checkerboard. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.
The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library
Related blocks
Grandmother's Cross
Cutting chart, sizes and sewing steps.
Prairie Queen
Cutting chart, sizes and sewing steps.
Chimney Sweep
Cutting chart, sizes and sewing steps.
Grandmother's Pride
Cutting chart, sizes and sewing steps.
Every classic block in the studio is in the quilt block library.