Jack in the Box Quilt Block

A free cutting chart for 6", 9" and 12" blocks, the units it is made of, and how to sew it, worked out by the same code that writes Quiltler's printable patterns.

Jack in the Box is a six-by-six block in a three-by-three layout: a large half-square triangle in each corner, accent half to the outside, plain background squares on the sides, and a four-patch in the center.

  • 6 × 6 grid
  • 6", 9" and 12" finished
  • 2 fabrics
The Jack in the Box block as the Quiltler studio draws it.

What the Jack in the Box block is made of

Every shape in a 12" block, by fabric, at its finished size.

FabricFinished shapes
Background4 squares (4"), 4 half-square triangles (4") and 2 squares (2")
Accent4 half-square triangles (4") and 2 squares (2")

The pattern sews it from 4 half-square triangle units (H1) and 1 four patch (U1).

Jack in the Box cutting chart

Cut sizes for one block at 6", 9" and 12" finished, with a ¼" seam allowance. These are the numbers a Quiltler pattern prints for the block: squares and rectangles are cut ½" larger than they finish, half-square triangles from squares ⅞" larger, and hourglasses and flying geese from squares 1¼" larger. Unit codes (H1, G1 and so on) match the sewing steps below.

6" finished block (1" grid, 6½" unfinished)

FabricCutFor
Background2 squares 2⅞"H1: half-square triangles, two at a time
Background4 squares 2½"Finishes at 2" square
Background2 squares 1½"Finishes at 1" square
Accent2 squares 2⅞"H1: half-square triangles, two at a time
Accent2 squares 1½"Finishes at 1" square

9" finished block (1½" grid, 9½" unfinished)

FabricCutFor
Background2 squares 3⅞"H1: half-square triangles, two at a time
Background4 squares 3½"Finishes at 3" square
Background2 squares 2"Finishes at 1½" square
Accent2 squares 3⅞"H1: half-square triangles, two at a time
Accent2 squares 2"Finishes at 1½" square

12" finished block (2" grid, 12½" unfinished)

FabricCutFor
Background2 squares 4⅞"H1: half-square triangles, two at a time
Background4 squares 4½"Finishes at 4" square
Background2 squares 2½"Finishes at 2" square
Accent2 squares 4⅞"H1: half-square triangles, two at a time
Accent2 squares 2½"Finishes at 2" square

How to sew a 12" Jack in the Box block

Make the units

  1. Pair each Accent square with a Background square, 4⅞" square, right sides together. Draw a line corner to corner on the back of the lighter one.
  2. Sew a quarter inch either side of the line, cut on the line and press open. Each pair makes two units.
  3. Make 4 units from 2 pairs. Each should measure 4½" square with seam allowance.

Sew unit U1 (four patch)

  1. Sew each row of Unit U1 together left to right, as the drawing shows. Press the seam allowances in alternate directions row to row so they nest.
  2. Join the rows, matching the seams where they meet.
  3. Each unit U1 should measure 4½" square including seam allowance. Check it against the drawing.

Sew the block

  1. The block takes 4 × H1 and 1 × unit U1; make them first.
  2. Lay the sections out as the drawing shows, 3 rows of 3. Sew the sections of each row together, pressing the seams in alternate directions row to row so they nest.
  3. Join the rows, matching the seams where they meet.
  4. The block should measure 12½" square including seam allowance. Check it against the drawing.

Check as you go: measure each unit before you sew it into a row. A unit that is a little small is easier to remake than a block that will not lie flat.

How many Jack in the Box blocks for a quilt?

With 12" blocks set edge to edge, no sashing and no border, the nearest whole number of blocks to the studio's throw and queen sizes:

QuiltBlocks across × downBlocksFinished top
Throw (60" × 72")5 × 63060" × 72"
Queen (90" × 108")8 × 97296" × 108"

Sashing and borders change the count. The quilt size calculator works it out for any block size, and the quilt sizes guide lists bed sizes.

Design with this block

Open the designer, press Go to Blocks at the top of the right panel, pick Classics and search for Jack in the Box. Click the block, then click a space on the quilt. It lands as ordinary pieces, so you can recolor any part of it.

Open the designer

The yardage and a printable pattern with this cutting chart come from the quilt you design. How to put a block on a quilt · Add a classic block to your library

Every classic block in the studio is in the quilt block library.

Calculators and guides for this block

Jack in the Box block FAQ

What do I cut for a 12" Jack in the Box block?

For one 12" finished Jack in the Box block, with a quarter-inch seam: Background: 2 squares 4⅞"; 4 squares 4½"; 2 squares 2½". Accent: 2 squares 4⅞"; 2 squares 2½".

How many Jack in the Box blocks make a throw quilt?

At 12" finished, 5 blocks across and 6 down, 30 in all, make a 60" × 72" top with no sashing or border.

What sizes can a Jack in the Box block be?

It is drafted on a 6 × 6 grid, so it works at any size that grid divides evenly. 6", 9" and 12" give 1", 1½" and 2" squares of the grid.

Design a Jack in the Box quilt

Lay the block out, try it in your own fabrics, and get the yardage and a printable pattern from the quilt you draw.

Design Online — Free Or get the companion app